欢迎光临济南宏泰食品机械有限公司网站!

全国咨询热线
 浅析切片机出现断线的应急措施
发布时间:2021-01-27 来源:http://www.chinafoodjx.com 发布人:admin

计算出焊接的头子完全跑出导轮需要多少的钢线计算公式,焊接处离导轮更后一根线的长度除以导轮槽距再乘以钢线绕导轮一圈的长度,并以0.2m/s的速度走线,当跑线过了500m时开启入线口大张力臂当跑线到了离200M就要出导轮的时候减少出线口张力臂直到焊头跑了收线轮上,并将工作台原有的高度上。

  The calculation formula of the number of steel wire required for the welding head to run out of the guide wheel is calculated. The length of the welding place is divided by the length of the last line of the guide wheel by the guide wheel and the length of the one circle around the guide wheel, and the line at the speed of 0.2m/s. When the running line passes through 500m, the large force arm of the entrance is opened, and when the running line goes to the 200M, the opening force arm of the outlet is reduced until the welding head runs. On the take-up wheel and the original height of the workbench.

  剪去断线处松散的钢线,并留出长于导轮间距>10cm的两个钢线头子。

  Cut out the loose steel wire at the broken line, and set aside two steel wire heads which are longer than the guide wheel spacing >10cm.

  焊接的钢线必有一段较长的一段松线,这一步我们要做的是将这一段送的钢线跑到导轮上去。先将工作台上升2mm开启砂浆用手指拨起松弛的钢线,并减少入线口的张力臂开启导轮以0.1m/s的速度走线直到松线较紧的部在导轮上然后松开手指。

  The welded steel wire must have a long loose section. What we need to do is to run the steel wire sent to the guide wheel. First raise the workbench 2mm to open the slack steel wire with the finger, and reduce the opening arm to open the guide wheel at the speed of 0.1m/s until the looser line is on the guide wheel and then loosens the finger.

  用先用粗砂纸将钢线的两个头子的直径砂少到原有钢线的1/2—2/3,砂的长度>5cm,在用细砂纸将钢线的表面砂光滑,更后用酒精将两个钢线头子洗干净。

  Using the coarse sand paper to reduce the diameter of the two heads of the steel wire to the 1/2 - 2/3 of the original steel wire, the length of the sand is >5cm, and the surface sand of the steel wire is smooth in the fine sand paper. Finally, the two steel wire heads are washed with alcohol.

  主要停机时间过久产生线痕的,从0—8m每隔一秒按下加速度直到速度升到8m/s左右,然后点开始切割。

  It mainly solves the problem that the line is long after downtime. It accelerations from 0 to 8m every second, until the speed rises to 8m/s, then the point starts to cut.

  取焊锡丝、焊锡膏、电烙铁将两个砂去5cm的钢线头子重合在一起并将其焊接,过程中用电烙铁重钢线的一头顺势焊道钢线的别一头途中两钢线头子必需完全重合不能让钢线翘起,如有则只有重新焊过,再用细砂纸将焊接的部分砂光滑并用酒精洗净。

  Soldering tin wire, solder paste, and electric soldering iron will reclose and weld two 5cm steel wire heads together. In the course of the process, the two wire heads of the steel wire of one end of the electric iron heavy steel line must be completely rejoined on the other side of the steel wire of the electric iron heavy steel line, for example, the steel wire is only rewelded and the welded part of the sand is smooth and washed with alcohol.

  本文由切丝切片机为您提供,我们的网站是:http://www.chinafoodjx.com我们将以全心全意的热情为您提供更的服务,欢迎您的访问!

  This article is provided by the cut silk slicing machine for you. Our website is: http://www.chinafoodjx.com we will provide you with more quality service and welcome your visit with wholehearted enthusiasm.

上一篇:多功能切菜机有哪些优势和技能?
下一篇:果蔬清洗机为什么要用臭氧?

相关新闻