全国咨询热线
不锈钢切丁机主要适用于肉类脱水蔬菜速冻蔬菜加工厂及食品酱菜行业加工各种根茎类蔬菜成正方体及长方体形状，其原理在于拨盘带动被切物体高速旋转，利用物体离心力，借助立刀将被切物体切成片状，然后经过圆盘切丝刀切成条状，并将被切物料送入横切断刀口，由横切断刀切成所需要的立方体或长方体切丁机工作一行程后，料仓存料约一到二毫米，刀片间隙小于10丝（0.1毫米）。
Stainless steel Dicer is mainly used in meat dehydrated vegetable quick frozen vegetable processing factory and food and pickle industry to process all kinds of root vegetables into cube and cuboid shape. Its principle is that the dial drives the object to rotate at a high speed, uses the centrifugal force of the object, with the help of the vertical knife to cut the object into slices, and then cuts into strips through the disc cutter, and sends the cut material to the horizontal cutting The cutting edge is cut into cubes or cuboids by the cross cutting cutter. After one stroke, the material in the bin is about 1 to 2 mm, and the blade gap is less than 10 wires (0.1 mm).
为了保证不锈钢切丁机使用的稳定性以及性，在操作不锈钢切丁机之前，使用者应做好必要的检查工作，其中：
In order to ensure the stability and efficiency of the stainless steel cutting machine, the user should do the necessary inspection before operating the stainless steel cutting machine
仔细检查切丁机是否存在缺损松问题，确保机器处于完好状态。
Carefully check the cutter for any defects and looseness to ensure that the machine is in good condition.
检查壳体内是否有异物存在，将壳体内异物掉，否则容易引起刀片的损坏。
Check whether there is any foreign matter in the shell, and remove the foreign matter in the shell, otherwise it is easy to cause damage to the blade.
清理操作场地，检查电源电压是否与本机使用电压相符，接地 标志处是否可靠连接地线。合上开关按下“开”按钮，检查转向是否正确（面对推料拨盘，推料拨盘逆时针方向旋转为正确），否则，切断电源调整接线。
Clean the operation site, check whether the power supply voltage is consistent with the use voltage of the machine, and whether the ground wire is reliably connected at the grounding mark. Close the switch and press the "on" button to check whether the steering direction is correct (in the face of the pusher dial, the pusher dial rotates counterclockwise to be correct). Otherwise, cut off the power supply and adjust the wiring.
接通水源，以备使用。
Connect the water source for use.
在不锈钢切丁机的使用中，使用者应注意以下几点要求：
In the use of stainless steel cutting machine, the user should pay attention to the following requirements:
，应将被切物料洗净去杂，如果被切物料混有沙石与泥块，刀刃口与刀板容易损坏和磨钝。物料zui大切割直径应不超过100mm，如果大于此直径须分块。
First of all, the materials to be cut should be cleaned to remove impurities. If the materials to be cut are mixed with sand and mud, the blade and blade are easy to be damaged and blunt. The large cutting diameter of material Zui shall not exceed 100mm. If it is larger than this diameter, it shall be divided into blocks.
按下启动按钮电机运转。（如上盖未压合在机架上，不能压合开关XK，线路不通，电机不能运转）
Press the start button to run the motor. (the upper cover is not pressed on the rack, the switch XK cannot be pressed, the line is blocked, and the motor cannot operate.)
将被切物料从料斗均匀连续投入进料斗中，在推料拨盘的作用下，被切片刀切割成所要求的厚度接着被圆盘切丝刀切成条状，zui后被横切断刀切成方块。
The cut material is uniformly and continuously put into the feed hopper from the hopper. Under the action of the pushing dial, it is cut to the required thickness by the slicing knife, then cut into strips by the disc cutter, and then cut into squares by the cross cutter after Zui.
切丁机规格的调整：是通过调整切片厚度，更换圆盘切丝刀和横切断刀来改变的。
Specification adjustment of the Dicer: it is changed by adjusting slice thickness, replacing disc cutter and cross cutter.
机器工作时，切勿将手及其他异物放入壳体中，以免发生危险。
When the machine is working, do not put hands and other foreign matters into the shell to avoid danger.
本文来自：切丁切块机更多的内容请点击：http://www.chinafoodjx.com我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！
This article comes from: Dicer more content please click: http://www.chinafoodjx.com we will provide a satisfactory service for your questions, welcome your call!
