欢迎光临济南宏泰食品机械有限公司网站!

全国咨询热线
切片机行业有哪些科技转变?
发布时间:2020-05-05 来源:http://www.chinafoodjx.com 发布人:admin

切片机是目前国内研制生产的产品,它广泛地应用于科研、教学、化工、医疗卫生等单位,专切新鲜的或经过固定的动、植物标本,特别是新鲜的脑组织。
Slicer is a product developed and produced in our country. It is widely used in scientific research, teaching, chemical industry, medical and health units. It specially cuts fresh or fixed animal and plant specimens, especially fresh brain tissue.
切片机切片时组织标本不需冰冻或包埋,为此,样品片避免了冰晶破坏,还能保持样品活性和细胞良好形态,给“免疫细胞化学研究 ”以及“脊髓和脑薄片的神经生物学研究”提供了良好条件,是当代电镜、解剖、组胚、生理、医院、化工等实验系统zui理想的快速制样理想切片仪器。切片机经过科学院上海生理研究所、复旦大学、第二军医大学、北京大学、北京协和医院、广州中山大学等单位使用证明,切片机切固定的脑和脊髓等组织,zui薄可切到10微米,新鲜的脑、心、肾等组织zui薄可切到30微米,且切片完整,片面光滑,染色均匀,其主要技术指标达到国外同类产品水平。
In order to avoid the destruction of ice crystal and keep the activity of the sample and the good shape of the cell, we need not freeze or embed the tissue specimen when slicing by the microtome ”And "neurobiological study of spinal cord and brain slice" provides good conditions, which is an ideal instrument for rapid sample preparation of Zui experimental system of electron microscopy, anatomy, embryo formation, physiology, hospital, chemical industry, etc. The slicer has been used by Shanghai Institute of physiology, Fudan University, the Second Military Medical University, Peking University, Peking Union Medical College, Guangzhou Zhongshan University and other units. It has been proved that the slicer can cut the fixed brain and spinal cord and other tissues. The thin Zui can be cut to 10 microns. The thin Zui of fresh brain, heart, kidney and other tissues can be cut to 30 microns. The slicer is complete, one-sided and smooth, with uniform staining The main technical indicators have reached the level of similar products abroad.
通常来讲,切片机的操作阐明包含开机和切片这两部分。开启切片机主机电源,翻开开关,运用箱体温度设置按钮设置切片时所需的温度,这时温度显现窗口会同步显现设置的温度。设置好后,过5秒后,会显现实践温度。同时,咱们也能够随时查看设置的温度巨细。*次开机时,切片机应经过基准时刻设置按钮设置一个基准时刻,经过除霜时刻设置按钮来设置除霜时刻。假如需求手动除霜,则应先按下手动除霜按钮,听到峰鸣音后,按下疾速制冷按钮可进行冷冻台的除霜,按下箱体温度设置按钮则是箱体除霜。如要关闭,只要按此次序再按一次就能够了。

切丝切片机
Generally speaking, the operation of the slicer includes two parts: startup and slicing. Turn on the main power of the slicer, turn on the switch, and use the box temperature setting button to set the required temperature for slicing. At this time, the temperature display window will synchronously display the set temperature. After setting, after 5 seconds, the practice temperature will appear. At the same time, we can check the temperature at any time. *During the secondary startup, the slicer shall set a reference time through the setting button of the reference time, and set the defrosting time through the setting button of the defrosting time. If manual defrosting is required, press the manual defrosting button first. After hearing the peak sound, press the fast cooling button to defrost the freezer. Press the box temperature setting button to defrost the box. To close, just press again in this order.
切片机能够运用厚度调理旋钮来调理切片厚度,装置刀片时应调整好切片角度。切片前,先将样品进行冷却,要冷却透彻,然后放到切片机上,样品要接近刀口,并调整好平面。以后按下按钮,进行切片,切出的样品要平坦的进入防卷板与刀片之间的空地,zui终取出,进行染色观察。想要避免切片机的参数被更改,能够将键盘确定,经过控制面板上的键盘确定按钮。按下按钮5秒钟左右,当时刻窗口中的两个点中止闪耀时,就表明键盘现已被确定了,想要解锁办法同上。切片机再次开机前,应查看切片机内是不是有积水,如有应处理洁净后再开机,假如需求长时刻运用,那么可将其夜间的温度调零下十度以下,这么有利于维护切片机。
The slicer can use the thickness adjusting knob to adjust the slice thickness, and the slice angle should be adjusted when the blade is installed. Before slicing, first cool the sample thoroughly, and then put it on the slicer. The sample should be close to the knife edge, and the plane should be adjusted. After that, press the button to slice. The cut sample should enter the open space between the anti roll plate and the blade, and Zui finally takes it out for dyeing observation. To avoid the parameters of the slicer being changed, the keyboard can be determined through the keyboard determination button on the control panel. Press the button for about 5 seconds, when two points in the window stop flashing, it means that the keyboard has been determined, and the way to unlock is the same as above. Before the slicer is turned on again, check whether there is water in the slicer. If there is water in the slicer, clean it and then turn it on again. If it needs to be used for a long time, then adjust its temperature at night to below - 10 ℃, which is conducive to maintaining the slicer.
关于切丝切片机http://www.chinafoodjx.com就先介绍到这里了,相信大家在实际的工作中会用到相关知识,如果您有这方面的需要,欢迎前来选购。
About the slicer http://www.chinafoodjx.com introduced here, I believe you will use the relevant knowledge in the actual work, if you have this need, welcome to purchase.

上一篇:不锈钢切丁机使用前应该注意什么?
下一篇:那些不合理的切片机设计会让你抓狂?

相关新闻