欢迎光临济南宏泰食品机械有限公司官方网站!

全国咨询热线
当前位置:首页 > 公司动态 > 宏泰集团动态 >
切片机的切片技巧及其断线修理
发布时间:2021-08-05 15:25:25 来源:http://www.chinafoodjx.com 发布人:admin

为了能让切片机的切片效果理想,而且切片表面美观整齐,无毛刺,切片厚度均匀,稳定性能好等,关键取决于能否正确掌握切片机的切片技巧。首先是关于切片机的备料阶段,要知晓湿性的物料比干性的好切,太干燥的物料有可能会切成粉末状;可以把太干太硬的物料烘软,再进行切片;粘性很高的物料可以调高切片厚度。
In order to make the slicing effect of the slicer ideal, and the slicing surface is beautiful and neat, without burr, uniform slicing thickness and good stability, the key depends on whether the slicing skills of the slicer can be mastered correctly. The first is about the material preparation stage of the slicer. We should know that wet materials are easier to cut than dry materials, and too dry materials may be cut into powder; Materials that are too dry and too hard can be baked soft and then sliced; The slice thickness can be increased for materials with high viscosity.
其次是切片机的入料方式,入料时,小块状物料用塑料压模压住切片,否则会有物料跳动现象产生,切不到位;如果物料有点大时,可先将物料加工成符合入料口尺寸大小,再进行切片,这样才有可能实现令人满意的切片效果。
The second is the feeding mode of the slicer. During feeding, small pieces of materials are pressed by plastic die, otherwise there will be material jumping and cutting in place; If the material is a little large, the material can be processed to meet the size of the feeding port before slicing, so as to achieve satisfactory slicing effect.


若是切片机在切片过程中出现故障的话必须及时解决,比如说断线。首先是要计算出焊接的头子完全跑出导轮需要多少的钢线计算公式,焊接处离导轮一根线的长度除以导轮槽距再乘以钢线绕导轮一圈的长度,并以0.2m/s的速度走线,当跑线过了500m时开启入线口大张力臂当跑线到了离200M就要出导轮的时候,减少出线口张力臂直到焊头跑了收线轮上,并将工作台原有的高度上。
If the slicer fails in the slicing process, it must be solved in time, such as disconnection. The first is to calculate the calculation formula of how much steel wire is required for the welded head to completely run out of the guide wheel. The length of a wire from the welding point to the guide wheel is divided by the slot distance of the guide wheel, multiplied by the length of a circle of steel wire around the guide wheel, and the wire is routed at the speed of 0.2m/s. When the running line exceeds 500m, open the large tension arm at the wire inlet. When the running line is 200m away, it is about to leave the guide wheel, Reduce the tension arm at the outlet until the welding head runs on the take-up wheel and the original height of the workbench.
然后剪去切片机断线处松散的钢线,并留出长于导轮间距>10cm的两个钢线头子;焊接的钢线必有一段较长的一段松线,将这一段送的钢线跑到导轮上去。先将工作台上升2mm开启砂浆用手指拨起松弛的钢线,并减少入线口的张力臂开启导轮以0.1m/s的速度走线直到松线较紧的部在导轮上然后松开手指。
Then cut off the loose steel wire at the broken wire of the slicer, and leave two steel wire heads longer than the spacing of guide wheels > 10cm; The welded steel wire must have a long section of loose wire, and run this section of steel wire to the guide wheel. Firstly, raise the workbench by 2mm, open the mortar, pull up the loose steel wire with your fingers, reduce the tension arm at the wire inlet, open the guide wheel and route the wire at the speed of 0.1m/s until the tighter part of the loose wire is on the guide wheel, and then loosen your fingers.
先用粗砂纸将钢线的两个头子的直径砂少到原有钢线的1/2—2/3,砂的长度>5cm,在用细砂纸将钢线的表面砂光滑,用酒精将两个钢线头子洗干净。这是为了解决切片机停机时间过久产生线痕的。取焊锡丝、焊锡膏、电烙铁将两个砂去5cm的钢线头子重合在一起并将其焊接。
First, use coarse sandpaper to reduce the diameter of the two heads of the steel wire to 1 / 2-2 / 3 of the original steel wire, and the length of the sand is > 5cm. Then use fine sandpaper to smooth the surface of the steel wire, and wash the two heads of the steel wire with alcohol. This is to solve the problem of thread marks caused by too long shutdown time of slicer. Take the solder wire, solder paste and electric soldering iron, overlap the two steel wire heads with the sand removed by 5cm and weld them.

上一条 : 切丝切片机中容易损坏的地方是什么?

下一条 : 切丝切片机切削液流量不宜过大

相关新闻

曹经理
李经理
袁经理
4009909668