欢迎光临济南宏泰食品机械有限公司官方网站!

全国咨询热线
当前位置:首页 > 公司动态 > 宏泰集团动态 >
切丝切片机切削液流量不宜过大
发布时间:2021-07-30 15:31:17 来源:http://www.chinafoodjx.com 发布人:admin

当对主轴和刀环进行维修和调整时,切片机如果在切片后期的出现晶片崩边现象,这种情况很有可能是由于圆形刀片的因素引起的,通过上面的分析我们可知在切片时因为圆形刀片刀片的振动和内在摩擦力的存在从而引起晶片的振动,导致崩边现象的产生。这时可以采用重新张刀的方法,调整刀片刃口的同轴度,或者采用修刀的方法进而排除晶片崩边现象的发生。
When the spindle and knife ring are repaired and adjusted, if the chip edge collapse occurs in the later stage of slicing, it is likely to be caused by the factors of the circular blade. Through the above analysis, we can see that the vibration of the chip and the edge collapse are caused by the vibration of the circular blade and the existence of internal friction during slicing. At this time, the method of re tensioning the knife can be used to adjust the coaxiality of the blade edge, or the method of trimming the knife can be used to eliminate the occurrence of wafer edge collapse.
飞片现象就是指在晶片切割过程中,会泛起飞片的现象。这种现象在切薄片和晶片切割结束到石墨托板处时特别容易发生。这是因为刀片对晶片的摩擦力过大而使石墨托板承受不了,造成品片被刀片带走的现象。,从上面的分析可知,分条机刀片的刀片与晶片之间有切削液,刀片对晶片有摩擦力的作用,摩擦力的大小与切割面积和切削液流量成正比,所以采用减小切削液流量的办法可以有用解决飞片现象。


Flyer phenomenon refers to the phenomenon that wafers will take off in the process of wafer cutting. This phenomenon is particularly easy to occur when the sheet and wafer are cut to the graphite support plate. This is because the friction between the blade and the wafer is too large for the graphite support plate to bear, resulting in the phenomenon that the wafer is taken away by the blade., From the above analysis, it can be seen that there is cutting fluid between the blade and the wafer of the slitter blade, and the blade has the effect of friction on the wafer. The magnitude of friction is directly proportional to the cutting area and the cutting fluid flow. Therefore, the method of reducing the cutting fluid flow can effectively solve the flyer phenomenon.
从实际操纵中我们发现,当切割晶片的出刀口处有切削液滴下时,也会很轻易泛起飞片的现象,这是因为切削液流量过大,而使摩擦力增 大,造成飞片的现象。因此,切削液流量不宜过大,能够知足切割时刃口处的冷却和润滑的流量即可。
From the actual operation, we found that when the cutting fluid drops at the cutting edge of the cutting wafer, it will also easily take off the flake. This is because the friction increases due to the excessive flow of cutting fluid, resulting in the phenomenon of flying flake. Therefore, the cutting fluid flow should not be too large, which can meet the cooling and lubrication flow at the cutting edge during cutting.

上一条 : 切片机的切片技巧及其断线修理

下一条 : 生活中常用的切片机有哪些?

相关新闻

曹经理
李经理
袁经理
4009909668