全国咨询热线
切丝切片机出现异常如何处理?
How to deal with the abnormality of the slicer?
异常情况及处理方案:
Abnormal conditions and handling plan:
1. 绢丝切片机的半成品松弛时，与施胶不均匀、基材不均匀密切相关。这时，应调整弓辊，使其保持平整。
1. The relaxation of semi-finished products of silk slicer is closely related to the uneven sizing and substrate. At this time, the bow roll should be adjusted to keep it flat.
或将卷筒张力增大时，裁剪机用刀管压紧基材。
Or when the tension of the drum increases, the cutter presses the base material with a knife tube.
2、半成品在卷绕起皱时，可适当增大张力缸压力。当卷绕成品运行时，卷绕轴是否张力
2. The pressure of tension cylinder can be increased properly when the semi-finished product is winding and wrinkling. Whether the winding shaft is under tension when the winding finished product is running
紧绷时，或与胶水有密切关系时
When tight or closely related to glue
3.卷取轴张力设定:
3. Coiling shaft tension setting:
卷筒轴上胶带的张力由张力调节螺母控制。
The tension of the tape on the drum shaft is controlled by the tension adjusting nut.
顺时针旋转螺母，拧紧胶带，逆时针旋转螺母。
Turn the nut clockwise, tighten the tape, and turn the nut counterclockwise.
4. 卷取轴处理不均匀:
4. Uneven treatment of coiling shaft:
检查左右链轮是否松脱。
Check whether the left and right sprockets are loose.
B安装四个绕线轴。侧边机对两侧进行水平调整，并校正位置。通过右内链轮两侧的调节螺丝进行调节。
B install the four spools. The side machine makes horizontal adjustment on both sides and corrects the position. Adjust by adjusting screws on both sides of the right inner sprocket.
调整左边到所需的角度，然后从右边调整到水平。
First adjust the left side to the desired angle, then adjust the right side to horizontal.
5. 废卷取及调整:
5. Waste coiling and adjustment:
正确调整磨边轴上的衬套，使其与磨边位置对准。
Correctly adjust the bushing on the edging shaft to align with the edging position.
B手动操作，直到有足够的边料被卷筒缠住为止。
B operate manually until there is enough leftover material entangled by the drum.
C机器运行时，边料自动卷取。
C. when the machine is running, the scraps are automatically coiled.
6. 感应开关功能及调节:
6. Induction switch function and regulation:
A本机感应开关为固定点开关，无需调整。
A. the inductive switch of this machine is fixed point switch without adjustment.
反感应:四点感应，三段长度数控线切割。计数器,稳定的刹车,
Anti induction: four point induction, three length CNC wire cutting. Counter, stable brake,
C开关轴感应:每个开关轴一次，计数器累加一次，以计算成品数量。
C switch axis induction: once for each switch axis, the counter accumulates once to calculate the quantity of finished products.
以上就是如何处理切丝切片机的异常情况。如果您有任何其他问题，请随时联系我们的24小时客户服务解答您的所有问题。
The above is how to deal with the abnormal situation of the slicer. If you have any other questions, please feel free to contact our 24-hour customer service to answer all your questions.
